TRCVICTLR | Jon's Arm Reference

External register TRCVICTLR bits [31:0] are architecturally mapped to AArch64 System register TRCVICTLR[31:0].

This register is present only when FEAT_ETE is implemented and FEAT_TRC_EXT is implemented. Otherwise, direct accesses to TRCVICTLR are RES0.

Attributes

Field descriptions

Bits [31:27]

EXLEVEL_RL_EL2, bit [26]

When FEAT_RME is implemented:

Filter instruction trace for EL2 in Realm state.

EXLEVEL_RL_EL2	Meaning
0b0	When TRCVICTLR.EXLEVEL_NS_EL2 is 0 the trace unit generates instruction trace for EL2 in Realm state. When TRCVICTLR.EXLEVEL_NS_EL2 is 1 the trace unit does not generate instruction trace for EL2 in Realm state.
0b1	When TRCVICTLR.EXLEVEL_NS_EL2 is 0 the trace unit does not generate instruction trace for EL2 in Realm state. When TRCVICTLR.EXLEVEL_NS_EL2 is 1 the trace unit generates instruction trace for EL2 in Realm state.

EXLEVEL_RL_EL2

Meaning

0b0

When TRCVICTLR.EXLEVEL_NS_EL2 is 0 the trace unit generates instruction trace for EL2 in Realm state.

When TRCVICTLR.EXLEVEL_NS_EL2 is 1 the trace unit does not generate instruction trace for EL2 in Realm state.

0b1

When TRCVICTLR.EXLEVEL_NS_EL2 is 0 the trace unit does not generate instruction trace for EL2 in Realm state.

When TRCVICTLR.EXLEVEL_NS_EL2 is 1 the trace unit generates instruction trace for EL2 in Realm state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

EXLEVEL_RL_EL1, bit [25]

When FEAT_RME is implemented:

Filter instruction trace for EL1 in Realm state.

EXLEVEL_RL_EL1	Meaning
0b0	When TRCVICTLR.EXLEVEL_NS_EL1 is 0 the trace unit generates instruction trace for EL1 in Realm state. When TRCVICTLR.EXLEVEL_NS_EL1 is 1 the trace unit does not generate instruction trace for EL1 in Realm state.
0b1	When TRCVICTLR.EXLEVEL_NS_EL1 is 0 the trace unit does not generate instruction trace for EL1 in Realm state. When TRCVICTLR.EXLEVEL_NS_EL1 is 1 the trace unit generates instruction trace for EL1 in Realm state.

EXLEVEL_RL_EL1

Meaning

0b0

When TRCVICTLR.EXLEVEL_NS_EL1 is 0 the trace unit generates instruction trace for EL1 in Realm state.

When TRCVICTLR.EXLEVEL_NS_EL1 is 1 the trace unit does not generate instruction trace for EL1 in Realm state.

0b1

When TRCVICTLR.EXLEVEL_NS_EL1 is 0 the trace unit does not generate instruction trace for EL1 in Realm state.

When TRCVICTLR.EXLEVEL_NS_EL1 is 1 the trace unit generates instruction trace for EL1 in Realm state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

EXLEVEL_RL_EL0, bit [24]

When FEAT_RME is implemented:

Filter instruction trace for EL0 in Realm state.

EXLEVEL_RL_EL0	Meaning
0b0	When TRCVICTLR.EXLEVEL_NS_EL0 is 0 the trace unit generates instruction trace for EL0 in Realm state. When TRCVICTLR.EXLEVEL_NS_EL0 is 1 the trace unit does not generate instruction trace for EL0 in Realm state.
0b1	When TRCVICTLR.EXLEVEL_NS_EL0 is 0 the trace unit does not generate instruction trace for EL0 in Realm state. When TRCVICTLR.EXLEVEL_NS_EL0 is 1 the trace unit generates instruction trace for EL0 in Realm state.

EXLEVEL_RL_EL0

Meaning

0b0

When TRCVICTLR.EXLEVEL_NS_EL0 is 0 the trace unit generates instruction trace for EL0 in Realm state.

When TRCVICTLR.EXLEVEL_NS_EL0 is 1 the trace unit does not generate instruction trace for EL0 in Realm state.

0b1

When TRCVICTLR.EXLEVEL_NS_EL0 is 0 the trace unit does not generate instruction trace for EL0 in Realm state.

When TRCVICTLR.EXLEVEL_NS_EL0 is 1 the trace unit generates instruction trace for EL0 in Realm state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

Bit [23]

EXLEVEL_NS_EL2, bit [22]

When Non-secure EL2 is implemented:

Filter instruction trace for EL2 in Non-secure state.

EXLEVEL_NS_EL2	Meaning
0b0	The trace unit generates instruction trace for EL2 in Non-secure state.
0b1	The trace unit does not generate instruction trace for EL2 in Non-secure state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

EXLEVEL_NS_EL1, bit [21]

When Non-secure EL1 is implemented:

Filter instruction trace for EL1 in Non-secure state.

EXLEVEL_NS_EL1	Meaning
0b0	The trace unit generates instruction trace for EL1 in Non-secure state.
0b1	The trace unit does not generate instruction trace for EL1 in Non-secure state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

EXLEVEL_NS_EL0, bit [20]

When Non-secure EL0 is implemented:

Filter instruction trace for EL0 in Non-secure state.

EXLEVEL_NS_EL0	Meaning
0b0	The trace unit generates instruction trace for EL0 in Non-secure state.
0b1	The trace unit does not generate instruction trace for EL0 in Non-secure state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

EXLEVEL_S_EL3, bit [19]

When EL3 is implemented:

Filter instruction trace for EL3.

EXLEVEL_S_EL3	Meaning
0b0	The trace unit generates instruction trace for EL3.
0b1	The trace unit does not generate instruction trace for EL3.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

EXLEVEL_S_EL2, bit [18]

When Secure EL2 is implemented:

Filter instruction trace for EL2 in Secure state.

EXLEVEL_S_EL2	Meaning
0b0	The trace unit generates instruction trace for EL2 in Secure state.
0b1	The trace unit does not generate instruction trace for EL2 in Secure state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

EXLEVEL_S_EL1, bit [17]

When Secure EL1 is implemented:

Filter instruction trace for EL1 in Secure state.

EXLEVEL_S_EL1	Meaning
0b0	The trace unit generates instruction trace for EL1 in Secure state.
0b1	The trace unit does not generate instruction trace for EL1 in Secure state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

EXLEVEL_S_EL0, bit [16]

When Secure EL0 is implemented:

Filter instruction trace for EL0 in Secure state.

EXLEVEL_S_EL0	Meaning
0b0	The trace unit generates instruction trace for EL0 in Secure state.
0b1	The trace unit does not generate instruction trace for EL0 in Secure state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

Bits [15:12]

TRCERR, bit [11]

When TRCIDR3.TRCERR == 1:

Controls the forced tracing of System Error exceptions.

TRCERR	Meaning
0b0	Forced tracing of System Error exceptions is disabled.
0b1	Forced tracing of System Error exceptions is enabled.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

TRCRESET, bit [10]

Controls the forced tracing of PE Resets.

TRCRESET	Meaning
0b0	Forced tracing of PE Resets is disabled.
0b1	Forced tracing of PE Resets is enabled.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

SSSTATUS, bit [9]

ViewInst start/stop function status.

SSSTATUS	Meaning
0b0	Stopped State. The ViewInst start/stop function is in the stopped state.
0b1	Started State. The ViewInst start/stop function is in the started state.

SSSTATUS

Meaning

0b0

Stopped State.

The ViewInst start/stop function is in the stopped state.

0b1

Started State.

The ViewInst start/stop function is in the started state.

Before software enables the trace unit, it must write to this field to set the initial state of the ViewInst start/stop function. If the ViewInst start/stop function is not used then set this field to 1. Arm recommends that the value of this field is set before each trace session begins.

If the trace unit becomes disabled while a start point or stop point is still speculative, then the value of TRCVICTLR.SSSTATUS is UNKNOWN and might represent the result of a speculative start point or stop point.

If software which is running on the PE being traced disables the trace unit, either by clearing TRCPRGCTLR.EN or locking the OS Lock, Arm recommends that a DSB and an ISB instruction are executed before disabling the trace unit to prevent any start points or stop points being speculative at the point of disabling the trace unit. This procedure assumes that all start points or stop points occur before the barrier instructions are executed. The procedure does not guarantee that there are no speculative start points or stop points when disabling, although it helps minimize the probability.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Accessing this field has the following behavior:

Access is RES1 if TRCIDR4.NUMACPAIRS == 0b0000 and TRCIDR4.NUMPC == 0b0000.
Otherwise, access to this field is RW.

Bit [8]

EVENT_TYPE, bit [7]

When TRCIDR4.NUMRSPAIR != 0b0000:

Chooses the type of Resource Selector.

EVENT_TYPE	Meaning
0b0	A single Resource Selector. TRCVICTLR.EVENT.SEL[4:0] selects the single Resource Selector, from 0-31, used to activate the resource event.
0b1	A Boolean-combined pair of Resource Selectors. TRCVICTLR.EVENT.SEL[3:0] selects the Resource Selector pair, from 0-15, that has a Boolean function that is applied to it whose output is used to activate the resource event. TRCVICTLR.EVENT.SEL[4] is RES0.

EVENT_TYPE

Meaning

0b0

A single Resource Selector.

TRCVICTLR.EVENT.SEL[4:0] selects the single Resource Selector, from 0-31, used to activate the resource event.

0b1

A Boolean-combined pair of Resource Selectors.

TRCVICTLR.EVENT.SEL[3:0] selects the Resource Selector pair, from 0-15, that has a Boolean function that is applied to it whose output is used to activate the resource event. TRCVICTLR.EVENT.SEL[4] is RES0.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

Otherwise:

Bits [6:5]

Bits[4:0]

When TRCIDR4.NUMRSPAIR != 0b0000:

EVENT_SEL, bits [4:0] of bits [4:0]

Defines the selected Resource Selector or pair of Resource Selectors. TRCVICTLR.EVENT.TYPE controls whether TRCVICTLR.EVENT.SEL is the index of a single Resource Selector, or the index of a pair of Resource Selectors.

If an unimplemented Resource Selector is selected using this field, the behavior of the resource event is UNPREDICTABLE, and the resource event might fire or might not fire when the resources are not in the Paused state.

Selecting Resource Selector pair 0 using this field is UNPREDICTABLE, and the resource event might fire or might not fire when the resources are not in the Paused state.

The reset behavior of this field is:

On a Trace unit reset, this field resets to an architecturally UNKNOWN value.

When TRCIDR4.NUMRSPAIR == 0b0000:

Reserved, bits [4:0] of bits [4:0]

This field is reserved:

Bits [4:1] are RES0.
Bit [0] is RES1.

Otherwise:

Accessing TRCVICTLR

Reads from this register might return an UNKNOWN value if the trace unit is not in either of the Idle or Stable states.

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
RES0					EXLEVEL_RL_EL2	EXLEVEL_RL_EL1	EXLEVEL_RL_EL0	RES0	EXLEVEL_NS_EL2	EXLEVEL_NS_EL1	EXLEVEL_NS_EL0	EXLEVEL_S_EL3	EXLEVEL_S_EL2	EXLEVEL_S_EL1	EXLEVEL_S_EL0	RES0				TRCERR	TRCRESET	SSSTATUS	RES0	EVENT_TYPE	RES0		Bits[4:0]

TRCVICTLR: Trace ViewInst Main Control Register

Purpose

Configuration

Attributes

Field descriptions

Bits [31:27]

EXLEVEL_RL_EL2, bit [26]When FEAT_RME is implemented:

Otherwise:

EXLEVEL_RL_EL1, bit [25]When FEAT_RME is implemented:

Otherwise:

EXLEVEL_RL_EL0, bit [24]When FEAT_RME is implemented:

Otherwise:

Bit [23]

EXLEVEL_NS_EL2, bit [22]When Non-secure EL2 is implemented:

Otherwise:

EXLEVEL_NS_EL1, bit [21]When Non-secure EL1 is implemented:

Otherwise:

EXLEVEL_NS_EL0, bit [20]When Non-secure EL0 is implemented:

Otherwise:

EXLEVEL_S_EL3, bit [19]When EL3 is implemented:

Otherwise:

EXLEVEL_S_EL2, bit [18]When Secure EL2 is implemented:

Otherwise:

EXLEVEL_S_EL1, bit [17]When Secure EL1 is implemented:

Otherwise:

EXLEVEL_S_EL0, bit [16]When Secure EL0 is implemented:

Otherwise:

Bits [15:12]

TRCERR, bit [11]When TRCIDR3.TRCERR == 1:

Otherwise:

TRCRESET, bit [10]

SSSTATUS, bit [9]

Bit [8]

EVENT_TYPE, bit [7]When TRCIDR4.NUMRSPAIR != 0b0000:

Otherwise:

Bits [6:5]

Bits[4:0]When TRCIDR4.NUMRSPAIR != 0b0000:

EVENT_SEL, bits [4:0] of bits [4:0]

When TRCIDR4.NUMRSPAIR == 0b0000:

Reserved, bits [4:0] of bits [4:0]

Otherwise:

Accessing TRCVICTLR

TRCVICTLR can be accessed through the external debug interface:

EXLEVEL_RL_EL2, bit [26]

When FEAT_RME is implemented:

EXLEVEL_RL_EL1, bit [25]

When FEAT_RME is implemented:

EXLEVEL_RL_EL0, bit [24]

When FEAT_RME is implemented:

EXLEVEL_NS_EL2, bit [22]

When Non-secure EL2 is implemented:

EXLEVEL_NS_EL1, bit [21]

When Non-secure EL1 is implemented:

EXLEVEL_NS_EL0, bit [20]

When Non-secure EL0 is implemented:

EXLEVEL_S_EL3, bit [19]

When EL3 is implemented:

EXLEVEL_S_EL2, bit [18]

When Secure EL2 is implemented:

EXLEVEL_S_EL1, bit [17]

When Secure EL1 is implemented:

EXLEVEL_S_EL0, bit [16]

When Secure EL0 is implemented:

TRCERR, bit [11]

When TRCIDR3.TRCERR == 1:

EVENT_TYPE, bit [7]

When TRCIDR4.NUMRSPAIR != 0b0000:

Bits[4:0]

When TRCIDR4.NUMRSPAIR != 0b0000: